View BP5034A24_1219978.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Regulator ICs
AC / DC converter unit
BP5034A24
The BP5034A24 is an AC / DC converter which can be used to supply direct current ()24V, DC 50mA) voltage from a commercial power supply (100V AC) with a small number of attachments. Using this unit enables simple, easy drive of sets using microcomputers, without using a transformer. It also allows the board in the set to be kept compact and lightweight. FApplications Power supplies of electric rice cookers and hot water pots, irons, electric carpets and other small household appliances; power supplies of illumination devices, fire and smoke alarms, sensors, and other warning devices FFeatures 1) Smaller and lighter weight than transformer systems. 2) Wide input voltage range. (80 to 120V for AC voltage conversion, 113 to 170V for DC voltage input) 3) DC voltage source (24V, 50mA) can be easily configured, with few attachments.
4) Since no transformer is used, the power supply board is less vulnerable to splitting or cracking from impact or shock. 5) Hybridization of the IC simplifies the manufacturing process for power supply circuit boards, and improves mass production capability of sets.
FAbsolute maximum ratings (Ta = 25_C)
FRecommended operating conditions
9
Regulator ICs
FElectrical characteristics (Ta = 25_C)
BP5034A24
FPin descriptions
FMeasurement circuit
Use a low-impedance product for switching power supplies for the output capacitor. 1 Pin 6 is the COMMON pin and is connected internally to pin 5. Use either both, or one or the other, as the COMMON pin. Keep open the other pins that are not used.
10
Regulator ICs
FBasic power supply circuit Half wave rectification circuit
BP5034A24
Full wave rectification circuit
FApplication example Example using electric rice cooker
11
Regulator ICs
BP5034A24
FSelecting attached components (1) Diodes The rectifying diodes used should fulfill the following conditions. In the absolute maximum ratings, the reverse surge current should be 400V or higher, the average rectifying current should be 0.5A or higher, and the forward surge voltage should be 20A or higher. One example of a product which meets these standards is the 1SR35-400A. (2) Capacitor for input voltage smoothing A capacitor with a larger capacitance produces a more stable output voltage, but increases the surge current when the power supply is turned on. The capacitor should have a withstand resistance of at least 200V. Please refer to Figure 5 for examples of recommended capacitance values. (3) Capacitor for output voltage smoothing This capacitor should have a low ESR. Capacitors designed for low-impedance switching power supplies are especially suitable. The ESR of the capacitor affects the output ripple voltage. Please refer to the table below for the names of products made by various manufacturers.
FOperation notes (1) The output current needs to be reduced as the ambient temperature rises. (2) Lead pins should be securely soldered. If common pins are not securely connected, or pins which are connected internally but which are not used are connected to other pins, irregular voltages could be produced, causing breakdowns and damage. (3) Over current and shorted circuit The over current limit is a drooping model. At 25_C, if over current which exceeds the absolute maximum ratings is produced intermittently, or is produced continuously for a total of one minute or longer, the product is vulnerable to damage. If there is any danger of the load
being shorted or over current being produced, always use a protective device such as a fuse. The fuse should have a fusion current of 0.5A. (4) Avoid subjecting this product to strong impact. (5) Regulations governing electrical products As a stand-alone product, this product is not subject to regulations governing electrical appliances. Please be aware, therefore, that applications must be submitted for sets and not for individual products. (6) Insulation This product is not insulated on the primary and secondary sides, and there is a danger of electrical shock if it is touched.
12
Regulator ICs
BP5034A24
(7) Connections with other devices Devices using this product should not be connected to other devices. If connected, insulation should be provided. (8) Pin noise voltage The test circuit diagram below (Figure 7) was used in the test whose results are shown in Figure 6.
13
Regulator ICs
FElectrical characteristic curves (measurement circuit is Fig 7)
BP5034A24
FExternal dimensions (Units: mm)
14

▲Up To Search▲

Price & Availability of BP5034A24

	To Download BP5034A24 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .